Technical data - ALPHA 550
| Wire length, single-sided processing min. | Wire length, single-sided processing min. |
| Wire length, processing on both sides min. | 60 mm |
| Wire length, processing on both sides (optional from) min. | 30 mm |
| Wire length max. | 65000 mm |
| Strip length side 1 min. | 0.1 mm |
| Strip length side 1 max. | 29.5 mm |
| Strip length side 2 min. | 0.1 mm |
| Strip length side 2 max. | 29.5 mm |
| Strip length, full stripping side 1 with wire outer diameter 1 mm/0.4 inch (blade in wire line) max. | 15 mm |
| Strip length, full stripping side 1 for wire outer diameter 2 mm/0.08 inch (blade in wire line) max. | 14.9 mm |
| Strip length, full stripping side 1 for wire outer diameter 4 mm/0.16 inch (blade in wire line) max. | 14.5 mm |
| Strip length, full stripping side 2 for wire outer diameter 1 mm/0.04 inch (blade in wire line) max. | 16 mm |
| Strip length, full stripping side 2 for wire outer diameter 2 mm/0.08 inch (blade in wire line) max. | 16 mm |
| Strip length, full stripping side 2 for wire outer diameter 4 mm/0.16 inch (blade in wire line) max. | 15.5 mm |
| Strip length, full stripping side 1 for wire outer diameter 1 mm/0.04 inch (blade next to wire line) max. | 29.5 mm |
| Strip length, full stripping side 1 for wire outer diameter 2 mm/0.08 inch (blade next to wire line) max. | 29.4 mm |
| Strip length, full stripping side 1 for wire outer diameter 4 mm/0.16 inch (blade next to wire line) max. | 29.2 mm |
| Strip length full stripping side 2 for wire outer diameter 1 mm/0.04 inch (blade next to wire line) max. | 29.5 mm |
| Strip length, full stripping side 2 for wire outer diameter 2 mm/0.08 inch (blade next to wire line) max. | 29.4 mm |
| Strip length, full stripping side 2 for wire outer diameter 4 mm/0.16 inch (blade next to wire line) max. | 29.2 mm |
| Strip length, partial stripping side 1 (blade in wire line) max. | 15.5 mm |
| Strip length, partial stripping side 2 (blade in wire line) max. | 15.5 mm |
| Strip length, partial stripping side 1 (blade next to wire line) max. | 35.5 mm |
| Strip length, partial stripping side 2 (blade next to wire line) max. | 35.5 mm |
| Wire outer diameter max. | 5.1 mm |
| Wire cross section min. | 0.13 mm² |
| Wire cross section max. | 6 mm² |
| Wire draw-in speed max. | 12 m/s |
| Noise level (without crimp modules) max. | 80 dB |
| Electrical connection | 3 × 208 – 480 V 50/60 Hz; 5.6 kVA |
| Electrical connection (optional) | 3 × 400 V, 50/60 Hz, neutral required, 5.6 kVA |
| Minimum permissible cross section of connection lines | 5 x 4 mm² |
| Wire protection/ground | 32 A |
| Compressed-air connection | 5 – 8 bar |
| Air consumption with wire length of 500 mm (19.7inch) (Crimp/Crimp) | 7 m³/h |
| Air consumption with wire length 500 mm & 19.7 inch (Seal Crimp/Seal Crimp) | 11 m³/h |
| Recommended operating pressure ±0.5 bar/7.25 psi | 6 bar |
| Operation outside the recommended operating pressure | Non-compliance with the recommended operating pressure can restrict the proper functioning of peripheral devices. Please also observe the technical data for peripheral devices. |
| Weight (approx.) | 1300 kg |
| Weight (including 2 crimp modules) approx. | 1300 kg |
| Length | 3825 mm |
| Length with basic module 2 m/78.74 inch | 3825 mm |
| Length with basic module 4 m/187.48 inch | 5770 mm |
| Width | 1525 mm |
| Height (with safety cover closed) | 1790 mm |
| Height (with safety cover open) | 2790 mm |
| Ambient temperature min. | 10 °C |
| Ambient temperature max. | 45 °C |
| Humidity, non-condensing | 30 - 90 % |
| Hard, tough wires | In the case of extremely hard, ductile or thick-stranded wires, processing might not be possible even within the cross section range. In case of doubt, Komax will be happy to provide processing samples of your wires. |
